Counter Coat epoxy
Counter Coat is perfect for Kitchen Countertops, Bar Counters, Table Tops, and Service Counters!
Works perfect on Formica countertops!! Cost effective and less aggravation and time!!

*Heat Resistant!      *Safe for Food!

 

Counter-Coat™ Application Instructions
Counter-Coat Application Instructions


Counter Top coating instructions step 1 STEP 1.
Work in a ventilated room; do not work near flames. Clean surfaces; remove any debris from counter top areas. Tape and cover all areas, including floor and cabinets, to protect from any spillage.
Counter paint instructions step 8 STEP 8.
Blend the top coat material as instructed per: "COLORED PRIME & BASE COAT MIXING INSTRUCTIONS"


counter top coating instructions step 2 STEP 2.
Sand the surface and sides with the supplied sanding paper. Wipe clean with rags to remove any sanding dust and debris. Fill fine cracks with Epoxy-Coat Acrylic Latex Caulk. Do NOT use silicone caulk.
Counter coating instructions step 9 STEP 9.
Using the supplied squeegee spread the top coating material evenly over the counter area.


Counter top coating instructions step 3 STEP 3.
Blend the base coat material as instructed per: "COLORED PRIME COAT MIXING INSTRUCTIONS"
Counter top coating instructions step 10 STEP 10.
Using the second supplied 4" roller, roll out the top coating material evenly over the counter area and the outer perimeter if desired. Do not over roll, this can create bubbles.


Counter top coating instructions step 4 STEP 4.
Using the supplied squeegee, spread the base coating material evenly over the counter to cover entire area, including sides. Clean the squeegee will with a rag and xylene, as you will need it in step 9: DO NOT SOAK IN QYLENE. THIS WILL DESTROY THE SQUEEGEE.
Counter top coating instructions step 11 STEP 11.
After 24 hours, lightly sand surface. Wipe clean with rags to remove any sanding dust or debris. Blend the top coat material as instructed per: "TOP COAT MIXING INSTRUCTIONS".


Counter top coating instructions step 5 STEP 5.
Using the supplied 4" roller, roll out the base coating material evenly over the counter to entire area, including the outer perimeter edges.
Counter top coating instructions step 12 STEP 12.
Using the supplied squeegee spread the top coating material evenly over the counter area.


Counter top coating instructions step 6 STEP 6.
After the entire base coat has been applied evenly, apply the decorative flake chips in small amounts onto the counter top. Apply the flake evenly, assuring even coverage.
Counter top coating instructions step 13 STEP 13.
Using the third supplied 4" roller, roll out the top coating material evenly over the counter to area and the outer perimeter if desired. Do not over roll, this can create bubbles.


Counter top coating instructions step 7 STEP 7.
After 24 hours the excess flakes can be removed and remaining flake sanded to remove any high or excessive flake to create a smooth surface.
   
 



Counter top coating Base Coat Part A Counter top coating Base Coat Part B COLOR PRIMER COAT & BASE COAT MIXING INSTRUCTIONS:

    Rinse and dry the kit bucket with a clean rag prior to mixing. Install the supplied mixing tool into a high-speed drill motor. Pour 1 part Colored Prim Coat Part "B" (8 oz.) and 2 parts of Base Coat Part "A" (16 oz.) using the supplied measuring cup, then add Part "C" colorant to this mixture. Follow the guidelines for recommended mixing and coverage on the measuring cup.*

    NOTE: Measuring cup must be cleaned after each use.

    Base Coat: Same as above, but with no Part "C" added.

    Mix thoroughly with the mixing tool for 3 minutes, paying close attention to the bucket sides and raising and lowering of the mixing tools.

    Immediately poor all mixed contents in a line on the counter top. After mixing, you have up to 20 minutes of working time at 70 Degrees F (lower working time at higher temperature).

    Mixing must be very thorough (3 minutes) or the coating will not cure of clean up. Removal of the uncured epoxy will be costly and very time consuming.




Counter top coating Top Coat Part A Counter top coating Top Coat Part B TOP COAT MIXING INSTRUCTIONS:
  • Stir "A" & "B" in cans, then mix 1 PART "A" and 1 PART "B" (1:1 ratio by volume). Stir thoroughly for 3 minutes.
  • Do not apply below 50 degrees F
  • Pot life once mixed is 15 minutes
  • Surface to be coated must be clean, dry and sound
  • Do not put enamel over Top Coat
  • For recoating, wait 8 hours
  • Do not exceed recommended wet film thickness (5 mils dft)
  • Do not apply less than 300 sq/ ft/ per gallon
  • Please read product data sheet and MSDS sheet




Home Page | Instructions | Warranty Info. | Color Options | Purchase Kits | Countertop Photos | Helpful Tips | Data Sheets | Hours and Contact Info | Ask the Experts | Resources | Site Map | Link Exchange |

COMMERCIAL - INDUSTRIAL - INSTITUTIONAL - RESIDENTIAL
Counter Top Coatings From Counter-Coat.com

Performance Floor Coating and Paint Epoxy Applicators are Headquartered in Mount Clemens, Michigan but service the entire continental United States.
International Services & Representation, Performance Floor is an International Company Commercial/Industrial Concrete Paint - Wholesale Epoxy Coating Industrial - Garage Floor Paint If you are searching for Commercial Concrete Paint, Wholesale Epoxy Coating, Countertop Coatings or Industrial Garage Floor Paint. Performance Floor is the Company that can help! © 1981 - Performance Floor Coating Systems, INC.



Site Designed by Livingstondirect Web Design Services of Michigan Web Design | Web Site Maintenance | Web Hosting | Search engine optimization (SEO) | Domain Name Registration | Search Engine Submission
Epoxy-Coat | Performance Floor | Performance Industries | Performance Epoxy-Coat | Performance Roads | Toledo Floor



Office Use Only: Epoxy Floor Coatings Test Blog - All Flooring Links